430 lines
18 KiB
C++
430 lines
18 KiB
C++
/*
|
|
* SendDemo.cpp
|
|
*
|
|
* Demonstrates sending IR codes in standard format with address and command
|
|
*
|
|
* This file is part of Arduino-IRremote https://github.com/Arduino-IRremote/Arduino-IRremote.
|
|
*
|
|
************************************************************************************
|
|
* MIT License
|
|
*
|
|
* Copyright (c) 2020-2023 Armin Joachimsmeyer
|
|
*
|
|
* Permission is hereby granted, free of charge, to any person obtaining a copy
|
|
* of this software and associated documentation files (the "Software"), to deal
|
|
* in the Software without restriction, including without limitation the rights
|
|
* to use, copy, modify, merge, publish, distribute, sublicense, and/or sell
|
|
* copies of the Software, and to permit persons to whom the Software is furnished
|
|
* to do so, subject to the following conditions:
|
|
*
|
|
* The above copyright notice and this permission notice shall be included in all
|
|
* copies or substantial portions of the Software.
|
|
*
|
|
* THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR IMPLIED,
|
|
* INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY, FITNESS FOR A
|
|
* PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
|
|
* HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY, WHETHER IN AN ACTION OF
|
|
* CONTRACT, TORT OR OTHERWISE, ARISING FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE
|
|
* OR THE USE OR OTHER DEALINGS IN THE SOFTWARE.
|
|
*
|
|
************************************************************************************
|
|
*/
|
|
|
|
#include <Arduino.h>
|
|
|
|
#include "PinDefinitionsAndMore.h" // Define macros for input and output pin etc.
|
|
|
|
#define DISABLE_CODE_FOR_RECEIVER // Disables restarting receiver after each send. Saves 450 bytes program memory and 269 bytes RAM if receiving functions are not used.
|
|
|
|
//#define EXCLUDE_EXOTIC_PROTOCOLS // Saves around 240 bytes program memory if IrSender.write is used
|
|
//#define SEND_PWM_BY_TIMER // Disable carrier PWM generation in software and use (restricted) hardware PWM.
|
|
//#define USE_NO_SEND_PWM // Use no carrier PWM, just simulate an active low receiver signal. Overrides SEND_PWM_BY_TIMER definition
|
|
//#define NO_LED_FEEDBACK_CODE // Saves 566 bytes program memory
|
|
//#define USE_OPEN_DRAIN_OUTPUT_FOR_SEND_PIN // Use or simulate open drain output mode at send pin. Attention, active state of open drain is LOW, so connect the send LED between positive supply and send pin!
|
|
|
|
#include <IRremote.hpp>
|
|
|
|
#define DELAY_AFTER_SEND 2000
|
|
#define DELAY_AFTER_LOOP 5000
|
|
|
|
void setup() {
|
|
Serial.begin(115200);
|
|
|
|
#if defined(__AVR_ATmega32U4__) || defined(SERIAL_PORT_USBVIRTUAL) || defined(SERIAL_USB) /*stm32duino*/|| defined(USBCON) /*STM32_stm32*/|| defined(SERIALUSB_PID) || defined(ARDUINO_attiny3217)
|
|
delay(4000); // To be able to connect Serial monitor after reset or power up and before first print out. Do not wait for an attached Serial Monitor!
|
|
#endif
|
|
// Just to know which program is running on my Arduino
|
|
Serial.println(F("START " __FILE__ " from " __DATE__ "\r\nUsing library version " VERSION_IRREMOTE));
|
|
|
|
#if defined(IR_SEND_PIN)
|
|
IrSender.begin(); // Start with IR_SEND_PIN as send pin and enable feedback LED at default feedback LED pin
|
|
# if defined(IR_SEND_PIN_STRING)
|
|
Serial.println(F("Send IR signals at pin " IR_SEND_PIN_STRING));
|
|
# else
|
|
Serial.println(F("Send IR signals at pin " STR(IR_SEND_PIN)));
|
|
# endif
|
|
#else
|
|
IrSender.begin(3, ENABLE_LED_FEEDBACK, USE_DEFAULT_FEEDBACK_LED_PIN); // Specify send pin and enable feedback LED at default feedback LED pin
|
|
Serial.println(F("Send IR signals at pin 3"));
|
|
#endif
|
|
|
|
#if !defined(SEND_PWM_BY_TIMER)
|
|
/*
|
|
* Print internal software PWM signal generation info
|
|
*/
|
|
IrSender.enableIROut(38); // Call it with 38 kHz just to initialize the values printed below
|
|
Serial.print(F("Send signal mark duration is "));
|
|
Serial.print(IrSender.periodOnTimeMicros);
|
|
Serial.print(F(" us, pulse narrowing correction is "));
|
|
Serial.print(IrSender.getPulseCorrectionNanos());
|
|
Serial.print(F(" ns, total period is "));
|
|
Serial.print(IrSender.periodTimeMicros);
|
|
Serial.println(F(" us"));
|
|
#endif
|
|
}
|
|
|
|
/*
|
|
* Set up the data to be sent.
|
|
* For most protocols, the data is build up with a constant 8 (or 16 byte) address
|
|
* and a variable 8 bit command.
|
|
* There are exceptions like Sony and Denon, which have 5 bit address.
|
|
*/
|
|
uint16_t sAddress = 0x0102;
|
|
uint8_t sCommand = 0x34;
|
|
uint16_t s16BitCommand = 0x5634;
|
|
uint8_t sRepeats = 0;
|
|
|
|
void loop() {
|
|
/*
|
|
* Print values
|
|
*/
|
|
Serial.println();
|
|
Serial.print(F("address=0x"));
|
|
Serial.print(sAddress, HEX);
|
|
Serial.print(F(" command=0x"));
|
|
Serial.print(sCommand, HEX);
|
|
Serial.print(F(" repeats="));
|
|
Serial.println(sRepeats);
|
|
Serial.println();
|
|
Serial.println();
|
|
Serial.flush();
|
|
|
|
Serial.println(F("Send NEC with 8 bit address"));
|
|
Serial.flush();
|
|
IrSender.sendNEC(sAddress & 0xFF, sCommand, sRepeats);
|
|
delay(DELAY_AFTER_SEND); // delay must be greater than 5 ms (RECORD_GAP_MICROS), otherwise the receiver sees it as one long signal
|
|
|
|
Serial.println(F("Send NEC with 16 bit address"));
|
|
Serial.flush();
|
|
IrSender.sendNEC(sAddress, sCommand, sRepeats);
|
|
delay(DELAY_AFTER_SEND);
|
|
|
|
Serial.println(F("Send NEC2 with 16 bit address"));
|
|
Serial.flush();
|
|
IrSender.sendNEC2(sAddress, sCommand, sRepeats);
|
|
delay(DELAY_AFTER_SEND);
|
|
|
|
if (sRepeats == 0) {
|
|
#if FLASHEND >= 0x3FFF && (RAMEND >= 0x4FF || RAMSIZE >= 0x4FF) // For 16k flash or more, like ATtiny1604. Code does not fit in program memory of ATtiny85 etc.
|
|
/*
|
|
* Send constant values only once in this demo
|
|
*/
|
|
Serial.println(F("Sending NEC Pronto data with 8 bit address 0x80 and command 0x45 and no repeats"));
|
|
Serial.flush();
|
|
IrSender.sendPronto(F("0000 006D 0022 0000 015E 00AB " /* Pronto header + start bit */
|
|
"0017 0015 0017 0015 0017 0017 0015 0017 0017 0015 0017 0015 0017 0015 0017 003F " /* Lower address byte */
|
|
"0017 003F 0017 003E 0017 003F 0015 003F 0017 003E 0017 003F 0017 003E 0017 0015 " /* Upper address byte (inverted at 8 bit mode) */
|
|
"0017 003E 0017 0015 0017 003F 0017 0015 0017 0015 0017 0015 0017 003F 0017 0015 " /* command byte */
|
|
"0019 0013 0019 003C 0017 0015 0017 003F 0017 003E 0017 003F 0017 0015 0017 003E " /* inverted command byte */
|
|
"0017 0806"), 0); //stop bit, no repeat possible, because of missing repeat pattern
|
|
delay(DELAY_AFTER_SEND);
|
|
|
|
/*
|
|
* !!! The next data occupies 136 bytes RAM !!!
|
|
*/
|
|
Serial.println(
|
|
F("Send NEC sendRaw data with 8 bit address=0xFB04 and command 0x08 and exact timing (16 bit array format)"));
|
|
Serial.flush();
|
|
const uint16_t irSignal[] = { 9000, 4500/*Start bit*/, 560, 560, 560, 560, 560, 1690, 560,
|
|
560/*0010 0x4 of 16 bit address LSB first*/, 560, 560, 560, 560, 560, 560, 560, 560/*0000*/, 560, 1690, 560, 1690,
|
|
560, 560, 560, 1690/*1101 0xB*/, 560, 1690, 560, 1690, 560, 1690, 560, 1690/*1111*/, 560, 560, 560, 560, 560, 560,
|
|
560, 1690/*0001 0x08 of command LSB first*/, 560, 560, 560, 560, 560, 560, 560, 560/*0000 0x00*/, 560, 1690, 560,
|
|
1690, 560, 1690, 560, 560/*1110 Inverted 8 of command*/, 560, 1690, 560, 1690, 560, 1690, 560,
|
|
1690/*1111 inverted 0 of command*/, 560 /*stop bit*/}; // Using exact NEC timing
|
|
IrSender.sendRaw(irSignal, sizeof(irSignal) / sizeof(irSignal[0]), NEC_KHZ); // Note the approach used to automatically calculate the size of the array.
|
|
delay(DELAY_AFTER_SEND);
|
|
|
|
/*
|
|
* With sendNECRaw() you can send 32 bit combined codes
|
|
*/
|
|
Serial.println(F("Send ONKYO with 16 bit address 0x0102 and 16 bit command 0x0304 with NECRaw(0x03040102)"));
|
|
Serial.flush();
|
|
IrSender.sendNECRaw(0x03040102, sRepeats);
|
|
delay(DELAY_AFTER_SEND);
|
|
|
|
/*
|
|
* With Send sendNECMSB() you can send your old 32 bit codes.
|
|
* To convert one into the other, you must reverse the byte positions and then reverse all positions of each byte.
|
|
* Example:
|
|
* 0xCB340102 byte reverse -> 0x020134CB bit reverse-> 40802CD3
|
|
*/
|
|
Serial.println(F("Send ONKYO with 16 bit address 0x0102 and command 0x34 with old 32 bit format MSB first (0x40802CD3)"));
|
|
Serial.flush();
|
|
IrSender.sendNECMSB(0x40802CD3, 32, false);
|
|
delay(DELAY_AFTER_SEND);
|
|
#endif
|
|
|
|
Serial.println(F("Send Panasonic 0xB, 0x10 as 48 bit PulseDistance using ProtocolConstants"));
|
|
Serial.flush();
|
|
#if __INT_WIDTH__ < 32
|
|
IRRawDataType tRawData[] = { 0xB02002, 0xA010 }; // LSB of tRawData[0] is sent first
|
|
IrSender.sendPulseDistanceWidthFromArray(&KaseikyoProtocolConstants, &tRawData[0], 48, NO_REPEATS); // Panasonic is a Kaseikyo variant
|
|
#else
|
|
IrSender.sendPulseDistanceWidth(&KaseikyoProtocolConstants, 0xA010B02002, 48, NO_REPEATS); // Panasonic is a Kaseikyo variant
|
|
#endif
|
|
|
|
delay(DELAY_AFTER_SEND);
|
|
|
|
/*
|
|
* Send 2 Panasonic 48 bit codes as generic Pulse Distance data, once with LSB and once with MSB first
|
|
*/
|
|
Serial.println(F("Send Panasonic 0xB, 0x10 as generic 48 bit PulseDistance"));
|
|
Serial.println(F(" LSB first"));
|
|
Serial.flush();
|
|
#if __INT_WIDTH__ < 32
|
|
IrSender.sendPulseDistanceWidthFromArray(38, 3450, 1700, 450, 1250, 450, 400, &tRawData[0], 48,
|
|
PROTOCOL_IS_LSB_FIRST, 0, NO_REPEATS);
|
|
#else
|
|
IrSender.sendPulseDistanceWidth(38, 3450, 1700, 450, 1250, 450, 400, 0xA010B02002, 48, PROTOCOL_IS_LSB_FIRST,
|
|
0, NO_REPEATS);
|
|
#endif
|
|
delay(DELAY_AFTER_SEND);
|
|
|
|
// The same with MSB first. Use bit reversed raw data of LSB first part
|
|
Serial.println(F(" MSB first"));
|
|
#if __INT_WIDTH__ < 32
|
|
tRawData[0] = 0x40040D00; // MSB of tRawData[0] is sent first
|
|
tRawData[1] = 0x805;
|
|
IrSender.sendPulseDistanceWidthFromArray(38, 3450, 1700, 450, 1250, 450, 400, &tRawData[0], 48,
|
|
PROTOCOL_IS_MSB_FIRST, 0, NO_REPEATS);
|
|
#else
|
|
IrSender.sendPulseDistanceWidth(38, 3450, 1700, 450, 1250, 450, 400, 0x40040D000805, 48, PROTOCOL_IS_MSB_FIRST,
|
|
0, NO_REPEATS);
|
|
#endif
|
|
delay(DELAY_AFTER_SEND);
|
|
|
|
Serial.println(F("Send generic 72 bit PulseDistance 0x5A AFEDCBA9 87654321 LSB first"));
|
|
Serial.flush();
|
|
# if __INT_WIDTH__ < 32
|
|
tRawData[0] = 0x87654321; // LSB of tRawData[0] is sent first
|
|
tRawData[1] = 0xAFEDCBA9;
|
|
tRawData[2] = 0x5A;
|
|
IrSender.sendPulseDistanceWidthFromArray(38, 8900, 4450, 550, 1700, 550, 600, &tRawData[0], 72, PROTOCOL_IS_LSB_FIRST, 0,
|
|
NO_REPEATS);
|
|
# else
|
|
IRRawDataType tRawData[] = { 0xAFEDCBA987654321, 0x5A }; // LSB of tRawData[0] is sent first
|
|
IrSender.sendPulseDistanceWidthFromArray(38, 8900, 4450, 550, 1700, 550, 600, &tRawData[0], 72, PROTOCOL_IS_LSB_FIRST, 0, NO_REPEATS);
|
|
# endif
|
|
delay(DELAY_AFTER_SEND);
|
|
|
|
Serial.println(F("Send generic 52 bit PulseDistanceWidth 0xDCBA9 87654321 LSB first"));
|
|
Serial.flush();
|
|
// Real PulseDistanceWidth (constant bit length) does not require a stop bit
|
|
#if __INT_WIDTH__ < 32
|
|
IrSender.sendPulseDistanceWidthFromArray(38, 300, 600, 600, 300, 300, 600, &tRawData[0], 52,
|
|
PROTOCOL_IS_LSB_FIRST, 0, 0);
|
|
#else
|
|
IrSender.sendPulseDistanceWidth(38, 300, 600, 600, 300, 300, 600, 0xDCBA987654321, 52, PROTOCOL_IS_LSB_FIRST,
|
|
0, 0);
|
|
#endif
|
|
delay(DELAY_AFTER_SEND);
|
|
|
|
Serial.println(F("Send generic 32 bit PulseWidth 0x87654321 LSB first"));
|
|
Serial.flush();
|
|
// Real PulseDistanceWidth (constant bit length) does not require a stop bit
|
|
IrSender.sendPulseDistanceWidth(38, 1000, 500, 600, 300, 300, 300, 0x87654321, 32, PROTOCOL_IS_LSB_FIRST, 0, 0);
|
|
delay(DELAY_AFTER_SEND);
|
|
}
|
|
|
|
Serial.println(F("Send Onkyo (NEC with 16 bit command)"));
|
|
Serial.flush();
|
|
IrSender.sendOnkyo(sAddress, s16BitCommand, sRepeats);
|
|
delay(DELAY_AFTER_SEND);
|
|
|
|
Serial.println(F("Send Apple"));
|
|
Serial.flush();
|
|
IrSender.sendApple(sAddress & 0xFF, sCommand, sRepeats);
|
|
delay(DELAY_AFTER_SEND);
|
|
|
|
Serial.println(F("Send Panasonic"));
|
|
Serial.flush();
|
|
IrSender.sendPanasonic(sAddress & 0xFFF, sCommand, sRepeats);
|
|
delay(DELAY_AFTER_SEND);
|
|
|
|
Serial.println(F("Send Kaseikyo with 0x4711 as Vendor ID"));
|
|
Serial.flush();
|
|
IrSender.sendKaseikyo(sAddress & 0xFFF, sCommand, sRepeats, 0x4711);
|
|
delay(DELAY_AFTER_SEND);
|
|
|
|
Serial.println(F("Send Kaseikyo_Denon variant"));
|
|
Serial.flush();
|
|
IrSender.sendKaseikyo_Denon(sAddress & 0xFFF, sCommand, sRepeats);
|
|
delay(DELAY_AFTER_SEND);
|
|
|
|
Serial.println(F("Send Denon"));
|
|
Serial.flush();
|
|
IrSender.sendDenon(sAddress & 0x1F, sCommand, sRepeats);
|
|
delay(DELAY_AFTER_SEND);
|
|
|
|
Serial.println(F("Send Denon/Sharp variant"));
|
|
Serial.flush();
|
|
IrSender.sendSharp(sAddress & 0x1F, sCommand, sRepeats);
|
|
delay(DELAY_AFTER_SEND);
|
|
|
|
Serial.println(F("Send Sony/SIRCS with 7 command and 5 address bits"));
|
|
Serial.flush();
|
|
IrSender.sendSony(sAddress & 0x1F, sCommand & 0x7F, sRepeats);
|
|
delay(DELAY_AFTER_SEND);
|
|
|
|
Serial.println(F("Send Sony/SIRCS with 7 command and 8 address bits"));
|
|
Serial.flush();
|
|
IrSender.sendSony(sAddress & 0xFF, sCommand, sRepeats, SIRCS_15_PROTOCOL);
|
|
delay(DELAY_AFTER_SEND);
|
|
|
|
Serial.println(F("Send Sony/SIRCS with 7 command and 13 address bits"));
|
|
Serial.flush();
|
|
IrSender.sendSony(sAddress & 0x1FFF, sCommand & 0x7F, sRepeats, SIRCS_20_PROTOCOL);
|
|
delay(DELAY_AFTER_SEND);
|
|
|
|
Serial.println(F("Send Samsung 8 bit command"));
|
|
Serial.flush();
|
|
IrSender.sendSamsung(sAddress, sCommand, sRepeats);
|
|
delay(DELAY_AFTER_SEND);
|
|
|
|
Serial.println(F("Send Samsung 16 bit command"));
|
|
Serial.flush();
|
|
IrSender.sendSamsung(sAddress, s16BitCommand, sRepeats);
|
|
delay(DELAY_AFTER_SEND);
|
|
|
|
Serial.println(F("Send Samsung48 16 bit command"));
|
|
Serial.flush();
|
|
IrSender.sendSamsung48(sAddress, s16BitCommand, sRepeats);
|
|
delay(DELAY_AFTER_SEND);
|
|
|
|
Serial.println(F("Send RC5"));
|
|
Serial.flush();
|
|
IrSender.sendRC5(sAddress & 0x1F, sCommand & 0x3F, sRepeats, true); // 5 address, 6 command bits
|
|
delay(DELAY_AFTER_SEND);
|
|
|
|
Serial.println(F("Send RC5X with 7.th MSB of command set"));
|
|
Serial.flush();
|
|
IrSender.sendRC5(sAddress & 0x1F, (sCommand & 0x3F) + 0x40, sRepeats, true); // 5 address, 7 command bits
|
|
delay(DELAY_AFTER_SEND);
|
|
|
|
Serial.println(F("Send RC6"));
|
|
Serial.flush();
|
|
IrSender.sendRC6(sAddress, sCommand, sRepeats, true);
|
|
delay(DELAY_AFTER_SEND);
|
|
|
|
#if FLASHEND >= 0x3FFF && (RAMEND >= 0x4FF || RAMSIZE >= 0x4FF) // For 16k flash or more, like ATtiny1604. Code does not fit in program memory of ATtiny85 etc.
|
|
/*
|
|
* Next example how to use the IrSender.write function
|
|
*/
|
|
IRData IRSendData;
|
|
// prepare data
|
|
IRSendData.address = sAddress;
|
|
IRSendData.command = sCommand;
|
|
IRSendData.flags = IRDATA_FLAGS_EMPTY;
|
|
|
|
IRSendData.protocol = SAMSUNG;
|
|
Serial.print(F("Send "));
|
|
Serial.println(getProtocolString(IRSendData.protocol));
|
|
Serial.flush();
|
|
IrSender.write(&IRSendData, sRepeats);
|
|
delay(DELAY_AFTER_SEND);
|
|
|
|
IRSendData.protocol = JVC; // switch protocol
|
|
Serial.print(F("Send "));
|
|
Serial.println(getProtocolString(IRSendData.protocol));
|
|
Serial.flush();
|
|
IrSender.write(&IRSendData, sRepeats);
|
|
delay(DELAY_AFTER_SEND);
|
|
|
|
IRSendData.command = s16BitCommand; // LG support more than 8 bit command
|
|
|
|
IRSendData.protocol = SAMSUNG;
|
|
Serial.print(F("Send "));
|
|
Serial.println(getProtocolString(IRSendData.protocol));
|
|
Serial.flush();
|
|
IrSender.write(&IRSendData, sRepeats);
|
|
delay(DELAY_AFTER_SEND);
|
|
|
|
IRSendData.protocol = LG;
|
|
Serial.print(F("Send "));
|
|
Serial.println(getProtocolString(IRSendData.protocol));
|
|
Serial.flush();
|
|
IrSender.write(&IRSendData, sRepeats);
|
|
delay(DELAY_AFTER_SEND);
|
|
|
|
Serial.println(F("Send MagiQuest"));
|
|
Serial.flush();
|
|
IrSender.sendMagiQuest(0x6BCD0000 | (uint32_t) sAddress, s16BitCommand); // we have 31 bit address
|
|
delay(DELAY_AFTER_SEND);
|
|
|
|
// Bang&Olufsen must be sent with 455 kHz
|
|
// Serial.println(F("Send Bang&Olufsen"));
|
|
// Serial.flush();
|
|
// IrSender.sendBangOlufsen(sAddress, sCommand, sRepeats);
|
|
// delay(DELAY_AFTER_SEND);
|
|
|
|
IRSendData.protocol = BOSEWAVE;
|
|
Serial.println(F("Send Bosewave with no address and 8 command bits"));
|
|
Serial.flush();
|
|
IrSender.write(&IRSendData, sRepeats);
|
|
delay(DELAY_AFTER_SEND);
|
|
|
|
IRSendData.protocol = FAST;
|
|
Serial.print(F("Send "));
|
|
Serial.println(getProtocolString(IRSendData.protocol));
|
|
Serial.flush();
|
|
IrSender.write(&IRSendData, sRepeats);
|
|
delay(DELAY_AFTER_SEND);
|
|
|
|
/*
|
|
* LEGO is difficult to receive because of its short marks and spaces
|
|
*/
|
|
Serial.println(F("Send Lego with 2 channel and with 4 command bits"));
|
|
Serial.flush();
|
|
IrSender.sendLegoPowerFunctions(sAddress, sCommand, LEGO_MODE_COMBO, true);
|
|
delay(DELAY_AFTER_SEND);
|
|
|
|
#endif // FLASHEND
|
|
/*
|
|
* Force buffer overflow
|
|
*/
|
|
Serial.println(F("Force buffer overflow by sending 700 marks and spaces"));
|
|
for (unsigned int i = 0; i < 350; ++i) {
|
|
// 400 + 400 should be received as 8/8 and sometimes as 9/7 or 7/9 if compensation by MARK_EXCESS_MICROS is optimal.
|
|
// 210 + 540 = 750 should be received as 5/10 or 4/11 if compensation by MARK_EXCESS_MICROS is optimal.
|
|
IrSender.mark(210); // 8 pulses at 38 kHz
|
|
IrSender.space(540); // to fill up to 750 us
|
|
}
|
|
delay(DELAY_AFTER_SEND);
|
|
|
|
/*
|
|
* Increment values
|
|
* Also increment address just for demonstration, which normally makes no sense
|
|
*/
|
|
sAddress += 0x0101;
|
|
sCommand += 0x11;
|
|
s16BitCommand += 0x1111;
|
|
sRepeats++;
|
|
// clip repeats at 4
|
|
if (sRepeats > 4) {
|
|
sRepeats = 4;
|
|
}
|
|
|
|
delay(DELAY_AFTER_LOOP); // additional delay at the end of each loop
|
|
}
|
|
|